ชั้นเดิน

Fliegl SDS 390 Schubboden

Custom-Made Transport Solution
Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications.

Chassis
Fine-grained steel welded construction in lightweight design, up to the support legs, drawbar with interchangeable 2 kingpin
Laterally in the floor with lashing eye preparation (max. 13 pairs)
24 ton, 2-speed support winch, single-sided operation, with straight lower part, without thrust compensation
Extendable ladder at the rear
Door lock on the side
2 wheel chocks + holder
Aluminum side impact protection
Steel underrun protection with wide Fliegl mud flaps, foldable fender for light unit
Quarter panel fenders
Rear impact protection
Aluminum ladder approx. 3,550 mm, with holder on the side
Tarpaulin rod with bracket
1 plastic toolbox, with drawer and insert, w=650/h=520/d=670 mm, can be locked with a padlock
1 spare wheel holder for 1 spare wheel, with wheel fastening kit
Axles + Suspension
SAF disc brake axles with 430 mm disc diameter
Axle/suspension laser-aligned to reduce tire wear and fuel consumption
Air suspension
1st axle automatic lift axle, including forced lowering & starting assist, actuated 3x by the brakes (starting assist is functional up to an axle load exceeding 30% and a speed of max. 25 km/h)
Braking System
2-line pneumatic braking system, color-coded lines for easy servicing
Spring brake parking brake
2 non-interchangeable coupling heads at the front
EBS, electronic braking system with EBS socket at the front, without connecting cable
Note: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS!
with lifting and lowering valve
Vehicle Stability System
Wheels & Tires
385/55R22.5 according to manufacturer's choice
Steel rims, factory silver
Electrical System
Nsdpfoi Riwxex Am Ujwn
24 Volt, multi-chamber lights, yellow LED lighting on the side
2 white position lights at the front
2 white/red marker lights at the rear
2 x 7-pole and 1 x 15-pole non-interchangeable sockets at the front
Self-Loading System (SBS)
Hydraulic cylinder with sliding mechanism installed in the floor. 2-circuit hydraulic system.
Switching between forward/reverse operation is done electrically via remote control with cable.
-Shovel floor power supply via side marker light
Actuation hydraulically via truck auxiliary drive
Hydraulic connection with hose on the front wall and HDK screw connector NW = 48 mm,
Note: A 2-circuit hydraulic system is required!
Recommended pump performance:
Flow rate: 110 l/min
Pressure: 250 bar
Oil tank filling min: 100 l
Self-Loading System (SBS) Floor
Sliding floor with wear plate at the rear
Floor boards made of aluminum, 8 mm floor profile, ribbed design
SBS Tipper Body
Aluminum box tipper body, front and side walls made of aluminum hollow profiles, welded around the top with a wide special reinforcement profile made of aluminum, and welded with a special frame at the bottom.
Sliding wall for better unloading of the load, with reinforced tarpaulin flaps at the bottom.
Rear wall made of aluminum hollow profiles, as a 2-wing door, with a division of 1/2 to 1/2, framed all around with a special U-profile with stop and rubber seal, with 2 externally mounted swivel locking rods, locked at the top & bottom. Rear wall with mechanical safety locking, operation at the rear on the left in the direction of travel. With pivoting crossbar at the top. The door locks can be locked with a padlock.
Standing platfor

โฆษณานี้ได้รับการแปลโดยอัตโนมัติ อาจมีข้อผิดพลาดในการแปลได้