ลิฟท์เก็บของGmatick GmbH
Paternoster
ลิฟท์เก็บของ
Gmatick GmbH
Paternoster
ปีที่ผลิต
2025
สภาพ
ใหม่
ที่ตั้ง
Verl 

รูปภาพแสดงให้เห็น
แสดงแผนที่
ข้อมูลเกี่ยวกับเครื่องจักร
ราคาและสถานที่
- ที่ตั้ง:
- Ostlandweg 7, 33415 Verl, DE

โทร
รายละเอียดข้อเสนอ
- รหัสประกาศ:
- A4351506
- อัปเดต:
- อัปเดตล่าสุดเมื่อ 03.03.2568
คำอธิบาย
1A Gmatick Storage Paternoster (roll rack)
The foil storage Paternoster foils is suitable to use for the storage of all 3D-films, it is used as a high storage at the membrane press or as a space-saving storage solution for the 3D foils.
With our Paternoster you can storage on very small area approximately 2, 4m x 1, 2m a lot of film rolls (up to 32 rolls of a Ø 300 mm). The required film is thus immediately available at the push of button. Our Paternoster are available from 2.8 m up to 6, 0 m as standard Paternoster. Also special solutions are offered by us, please contact us, we will then find the right solution for your storage.
As additional equipment we offer center sleeves, a manual cutting station or the full automatic cutting device and we have also ionization solutions available at Gmatick.
• Storage rods ø 42.4 mm
• Sleeves inside Ø max. 82 mm,.
• Load chain as a hollow pin chain with a breaking load of 100 kN,
• Chain pitch is 50 mm hole to hole and this is the raster for the positioning of the mounting foil bars.
• Control with a key switch (dead man) for on / off
• Rotational speed of the chain is approx. 5.5 m / min
• Voltage 400 V, 3N; 50/60 Hz or as USA Version 480V 60Hz
• Mains cable with CEKON plug 16A fuse protection (by the customer) 10A slow blow
• ground load data at least 2, 2 kg / cm²
• Side covering over the entire height of the Paternoster, guards from 2, 2 m above floor to top edge of the Paternoster.
• Requirement for the installation of the Paternoster is a viable, flat and solid floor,
• Floating floors you can’t install a Paternoster. It is forbidden
Pgsdpfx Aeff Huweaysu
The foil storage Paternoster foils is suitable to use for the storage of all 3D-films, it is used as a high storage at the membrane press or as a space-saving storage solution for the 3D foils.
With our Paternoster you can storage on very small area approximately 2, 4m x 1, 2m a lot of film rolls (up to 32 rolls of a Ø 300 mm). The required film is thus immediately available at the push of button. Our Paternoster are available from 2.8 m up to 6, 0 m as standard Paternoster. Also special solutions are offered by us, please contact us, we will then find the right solution for your storage.
As additional equipment we offer center sleeves, a manual cutting station or the full automatic cutting device and we have also ionization solutions available at Gmatick.
• Storage rods ø 42.4 mm
• Sleeves inside Ø max. 82 mm,.
• Load chain as a hollow pin chain with a breaking load of 100 kN,
• Chain pitch is 50 mm hole to hole and this is the raster for the positioning of the mounting foil bars.
• Control with a key switch (dead man) for on / off
• Rotational speed of the chain is approx. 5.5 m / min
• Voltage 400 V, 3N; 50/60 Hz or as USA Version 480V 60Hz
• Mains cable with CEKON plug 16A fuse protection (by the customer) 10A slow blow
• ground load data at least 2, 2 kg / cm²
• Side covering over the entire height of the Paternoster, guards from 2, 2 m above floor to top edge of the Paternoster.
• Requirement for the installation of the Paternoster is a viable, flat and solid floor,
• Floating floors you can’t install a Paternoster. It is forbidden
Pgsdpfx Aeff Huweaysu
เอกสาร
ผู้จัดหา
หมายเหตุ: ลงทะเบียนฟรีหรือเข้าสู่ระบบ, เพื่อเข้าถึงข้อมูลทั้งหมด
ลงทะเบียนตั้งแต่: 2020
ส่งคำขอ
โทรศัพท์ & แฟกซ์
+49 1512 ... โฆษณา
ประกาศของคุณถูกลบเรียบร้อยแล้ว
เกิดข้อผิดพลาด










