โหลดต่ำ

Fliegl VTS 400

Customized Transport Solution
Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are carried out individually according to customer requirements.

Further Information
Low-loader trailer chassis
Steel welded construction
Turntable with heavy-duty ball bearing
Foldable rear support
2 support wedges with holder
Aluminum side impact protection
Splash guards at the rear over the entire width
Quarter panel fenders in front of the 1st axle
Extendable widening elements to 3,000 mm (not in rear slope)
(However, the track width of the construction machines or vehicles to be transported must not exceed
the outer frame width of 2,550 mm)
Storage compartment for wooden planks in the center of the loading area
Wooden planks 70 mm for widening to 3000 mm
Tie-down points for low-loader
1 pair of tie-down points on the gooseneck, each 5 tons
9 pairs of tie-down eyes embedded at the top and sides in the outer frame, each 10 tons
2 x at the front on the gooseneck
7 x in the low bed
6 pairs of tie-down holes in the outer frame of the low bed, each with 5 tons.
(for securing lashing straps)
Coupling device for trailer turntable
Podpoi Ri Izofx Aflegn
Drawbar with tested 50 mm drawbar eye
Axles + Suspension
SAF drum brake axles
Axle/chassis laser-aligned to reduce tire wear and fuel consumption
Parabolic suspension with maintenance-free steel-rubber bearing and mechanical incl.
Axle load equalization at the front and rear (lever equalization)
Wheels and tires
235 / 75 R 17.5
according to the manufacturer's choice
Steel rims in twin arrangement, factory silver
Braking system
2-line compressed air braking system
Spring brake parking brake
2 fail-safe coupling heads at the front, with connecting lines to the towing vehicle,
ABS and ALB, with ABS plug at the front, with connecting cable
Attention: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS!
Electrical system
24 Volt, multi-chamber lights, yellow LED lighting on the sides
2 white position lights at the front
2 white/red marker lights at the rear
1 LED warning light with holder, switched via side lights (light can be removed)
2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm
2 x 7-pin fail-safe plugs at the front, with connecting cable
Floor
Gooseneck at the front with steel/diamond plate
thereafter with 70 mm softwood floor, in the wheel arch area steel/diamond plate
Rear slope with 70 mm softwood floor
Ramps
Steel ramps 2,800 mm long, 750 mm wide, laterally movable
covered with wood
Hydraulically operated via tractor's auxiliary drive with throttle, operation on the left side
Hydraulic connection with quick-release coupling NW 10/3, incl. connecting hose
Operating instructions
At 10,000 kg axle load, an exemption permit is required, only indivisible loads are possible!!!
The stated total weight is technically possible; depending on the cargo, the total weight may not be reached while observing the permissible axle/support and saddle loads. (Poor driving and handling behavior possible due to incorrect load distribution)
Country of registration / Signs
Country of registration: Germany
with Dekra approval and certificate (according to §13 EG - FGV)
24/7 service hotline included
prepared for license plate holder, two-line
Contour marking with reflective strips according to ECE R 048, white on the sides and red at the rear
Painting
Frame DB 7350 Novagrau
10-year warranty against rusting
Drawbar galva

โฆษณานี้ได้รับการแปลโดยอัตโนมัติ อาจมีข้อผิดพลาดในการแปลได้